Automotive Bushings for Seat, Suspension, Steering, Chassis and Hinge Pivots

Automotive Bushings: the small pivots and slides that decide whether a mechanism feels tight or loose, from seat mechanisms and steering columns to suspension control arms, chassis joints and hinge pins. Machined to drawing or sample.

Where Are Bushings Used in a Vehicle?

Cutaway of a passenger car showing the steering column, suspension, seat frames, door hinge pins and drivetrain where automotive bushings sit
Cutaway of a passenger car showing the steering column, suspension, seat frames, hinge pins and drivetrain discussed below.

Automotive bushings are used at many moving joints and pivot points in a vehicle, from a sliding seat track to a loaded suspension pivot. They support shafts and pins, allow controlled movement, and help keep clearance between mating components within the required range. The exact position depends on the vehicle design.

Steering System

Bushings can be used around the steering column, steering shaft, steering linkage and other pivot points. These parts may rotate or oscillate repeatedly while carrying radial load, so automotive steering bushings have to guide the moving shaft or pin without allowing excessive clearance.

Suspension and Chassis

Automotive suspension bushings are commonly found around control arms, stabilizer linkages and other suspension pivot points. These positions move whenever the suspension responds to road conditions, and the bushing has to accommodate repeated movement while the sliding surface handles load, vibration and road shock.

SKF identifies stabilizer bar and track control arm bushings as automotive suspension applications. For shock absorber applications, see our dedicated Shock Absorber Bushings page.

Transmission and Gearbox

Bushings may support shafts and moving mechanisms inside a transmission. Depending on the design, the movement can be rotational or oscillating, and the bushing may also be exposed to oil, heat and changing loads.

Common positions include shaft supports, shift pivots and other moving transmission components. Automotive plain-bearing applications include main shafts, output shafts, reverse idlers, clutches and gear-shifting mechanisms.

Axles and Chassis Joints

Bushings can also be found around loaded axle and chassis joints, including king pins and other pivoting connections. Automotive chassis bushings at these pivots can see high radial loads and shock loads combined with relatively small oscillating movements.

Brake Mechanisms

Brake mechanisms use bushings at selected pivots and moving connections. Examples include caliper-related positions, pedal shafts and brake linkages.

Although the movement is usually small, the number of operating cycles can be high, so clearance and wear need to remain under control.

Seat Mechanisms

Automotive seat bushings can be used in the seat recliner pivot, the height adjustment linkage and the sliding tracks. The movement is normally slow, but the mechanism may be adjusted repeatedly over the vehicle's service life.

Hinges and Body Mechanisms

Automotive hinge bushings can be used in door hinges, hood hinges, trunk hinges and door-check mechanisms, where the hinge pin is the pivot. These are usually low-speed oscillating applications, and the bushing has to accommodate repeated opening and closing without developing excessive play.

Wiper and Linkage Mechanisms

Bushings can also be used around wiper pivots, linkage joints and pedal mechanisms. These parts may have relatively low loads but can experience a large number of operating cycles.

What Is the Bushing Actually Doing?

A bushing does more than hold two metal parts apart. What it does depends on the mechanism it sits in.

In a steering system

It controls the relationship between a shaft, housing or linkage at the steering column pivot.

In a suspension joint

It allows movement while carrying the load and controlling the position of the connected components around the suspension pivot.

In a seat mechanism

It provides a controlled sliding or pivoting surface.

In a hinge

It supports repeated low-speed movement at the hinge pivot while limiting clearance.

The bushing therefore has to work together with the shaft, pin, housing and surrounding components. A material that works well at one pivot may not work at another, even when the car bushings have similar dimensions.

What Causes an Automotive Bushing to Wear?

Bushing failure is usually related to the actual operating conditions at the pivot rather than simply the number of years the vehicle has been in service. Common causes include:

1

Excessive Load

A bushing can wear quickly when the actual radial or impact load is higher than the original design condition. This can happen after a vehicle modification, component replacement or change in operating conditions.

2

Repeated Oscillation

Many automotive bushings do not rotate continuously. They move through a limited angle again and again, so the sliding stays inside the same small arc, and control arms, steering linkages, hinges and seat mechanisms are typical pivot positions. Repeated movement can gradually increase the clearance between the bushing and shaft.

3

Vibration and Shock

Suspension and chassis positions are exposed to road-induced vibration and shock. If the bushing cannot control movement properly, the connected components may begin to move more than intended, which is how automotive suspension bushings at a control arm or a stabilizer link end up with play.

4

Poor Lubrication

Some bushings depend on grease or oil. If lubrication is lost, contaminated or not reaching the sliding surface at the pivot, friction and wear can increase rapidly.

5

Worn Shaft or Housing

Replacing the bushing does not repair a damaged mating surface. A worn shaft can leave excessive clearance at the pivot even after a new bushing is installed, and an oversized housing can affect the fit and retention of the replacement.

6

Temperature and Environment

Temperature, and the thermal environment around the pivot, can affect the performance and service life of the sliding material. Water, dust, road salt, oil and other contaminants can also change the way the bushing and mating surface wear.

Check the cause before choosing the replacement. A bushing that failed because the shaft was already worn or the housing bore was oversized will fail again in the same position.

How Do You Know an Automotive Bushing Needs to Be Replaced?

Do not wait for the bushing to fail completely. The first indication is often a change in the movement of the mechanism, and the checks below cover automotive seat bushings, car seat bushings and the other positions on this page.

Steering

Possible signs include:

  • Excessive play
  • Unwanted movement around the shaft or linkage
  • Noise during steering movement
  • Clearance that is greater than the specified value

The source of the problem should be checked before replacing the part. A worn shaft or another steering component can produce similar symptoms, so inspect the automotive steering bushings at the column pivot together with the shaft and the housing.

Suspension and Chassis

Possible signs include:

  • Increased movement at a joint
  • Knocking or abnormal noise
  • Visible wear
  • Excessive clearance
  • Abnormal movement of the control arm or linkage

Automotive chassis bushings should be inspected together with the pin, shaft and housing at the control arm pivot and the stabilizer link.

Seat Mechanisms

A worn automotive seat bushing may cause:

  • Excessive side movement
  • Loose adjustment
  • Increased play in the recliner pivot
  • Noise during adjustment

Hinges

Worn automotive hinge bushings may result in:

  • Door or hood play
  • Increased hinge clearance
  • Noise during opening or closing
  • Movement that is no longer properly controlled

The hinge pin should be inspected at the same time, because wear at the hinge pivot and wear on the pin go together.

What Happens If a Worn Bushing Is Left in Service?

A worn bushing does not always fail suddenly.

The bigger problem is that increasing clearance can change how the surrounding mechanism carries load.

Suspension pivot

Excessive clearance in a suspension joint can allow more unwanted movement between connected components under load.

Steering pivot

Increased clearance can affect the relationship between the shaft or linkage and its housing, and it changes the way the linkage carries load.

Hinge pivot

Continued clearance can increase load on the hinge pin and surrounding structure, and worn automotive hinge bushings let a door or a hood drop instead of holding its line.

Seat pivot

Continued wear can make the adjustment mechanism loose and noisy, and the seat no longer holds its position under load.

The result is not always a failed bushing alone. Continued operation can increase wear on the mating shaft, pin, housing or other connected components, which is why the condition of the surrounding parts should be checked when replacing car bushings.

Why Does a New Bushing Sometimes Wear Out Quickly?

Replacing the bushing, which is the sliding part of the joint, is only part of the repair. If a new bushing wears out much sooner than expected, check the application rather than assuming the replacement part was defective.

1

Check the Shaft

Measure the shaft or pin instead of relying on its nominal dimension. Look for:

  • Wear
  • Scoring
  • Corrosion
  • Out-of-round condition
  • Incorrect surface finish
2

Check the Housing

The housing bore affects the fit and support of the bushing. An oversized or damaged bore can prevent the new bushing from working as intended.

3

Check the Actual Movement

Determine whether the movement is continuous rotation, limited-angle oscillation, reciprocating movement or start-stop movement. This makes a major difference to bushing selection, because automotive steering bushings oscillate while a sliding seat track and a rotating shaft load the bore in different ways.

4

Check the Load

Do not use only the vehicle's nominal weight. The bushing may see a much higher local load at a suspension joint, steering linkage or chassis pivot.

Peak and shock loads are important where applicable.

5

Check Lubrication

Confirm whether the application is dry running, grease lubricated, oil lubricated or intermittently lubricated. The lubrication condition should match the sliding speed and the bushing design.

Automotive Bushing Selection: What Should the Engineer Check?

Before selecting a replacement, collect the actual working conditions. These are the nine points that decide the material, the wall thickness and the fit, whether you are buying car bushings from a catalogue or a one-off batch to drawing.

1

Shaft or Pin Diameter

What is the measured diameter, and is the shaft still within tolerance? At the steering column pivot, a suspension pivot or a hinge pin, this measurement decides the running clearance.

2

Housing Bore

What is the actual housing diameter, and has the bore become oversized after previous wear? The bore carries the outside diameter of the bushing.

3

Load

What is the normal radial load, and is there an impact or peak load? Automotive suspension bushings at a control arm and automotive chassis bushings at a loaded axle joint do not see the same figure as a sliding seat track.

4

Movement

Does the bushing rotate continuously, oscillate through an angle, or move back and forth?

5

Speed

For rotating or sliding applications, what is the actual operating speed?

6

Temperature

What is the normal temperature, and what is the maximum temperature during operation? Electric vehicle bushings sit in a thermal environment that runs warmer than the rest of the chassis.

7

Lubrication

Is the bushing expected to run dry, with grease, or with oil? The answer sets the sliding layer.

8

Environment

Will it be exposed to:

  • Water
  • Road salt
  • Dust
  • Oil
  • Fuel
  • Cleaning chemicals
9

Required Life

How many cycles or operating hours does the bushing need to achieve?

These details are more useful than simply saying that the part is for an automobile.

What About EV Bushings?

Electric vehicles do not make every bushing application different. The important changes are found in specific systems, and EV bushings are usually the ones closest to the motor, the e-axle and the battery pack.

An EV may contain electric motors, e-axles, battery systems, power electronics and different thermal-management components. These systems introduce their own combinations of load, vibration, temperature and packaging constraints, and electric vehicle bushings at a motor mount pivot or an e-axle pivot sit in a thermal environment that runs warmer than the cabin. GGB identifies e-motors, e-axles, power steering, battery cooling and e-compressors among EV applications for plain bearings.

The NVH environment can also be different. With less engine noise, mechanical noise and vibration from other components may become more noticeable, so NVH requirements carry more weight in the selection of EV bushings than they do on a combustion vehicle.

For an EV bushing, check the actual:

  • Load
  • Movement
  • Vibration
  • NVH requirement
  • Temperature
  • Installation space
  • Lubrication condition

Do not select an EV bushing only because it is described as an electric vehicle application. The position, the load and the operating conditions still determine the required bearing construction.

Which Bushing Fits Your Automotive Application?

Automotive applicationTypical bushing positionSuitable GLARY bushing series
SteeringSteering column, steering linkage, steering shaftComposite, Bimetal, Bronze Wrapped
Suspension & ChassisControl arm, stabilizer linkage, suspension jointsComposite, Bimetal, Bronze Wrapped
TransmissionMain shaft, output shaft, shift mechanismComposite, Bimetal, Sintered
Axles & KingpinsKing pin, axle joints, loaded pivot pointsBimetal, Bronze Wrapped, Composite
Brake SystemBrake caliper, pedal shaft, brake linkageComposite, Bimetal, Bronze Wrapped
Engine & Auxiliary SystemsPumps, belt tensioners, pulley mechanismsComposite, Bimetal, Sintered
Automotive SeatsSeat recliner pivot, height adjustment, sliding mechanismPOM Composite, PTFE Composite, Sintered
Automotive HingesDoor hinge, hood hinge, trunk hingePOM Composite, PTFE Composite, Bronze Wrapped
Wiper & LinkageWiper pivot, linkage, pedal mechanismsPOM Composite, PTFE Composite, Sintered
EV ApplicationsE-axle, e-motor and other moving mechanismsDepends on load, speed, temperature and lubrication

These are application-level guidelines, not a substitute for engineering selection. The final automotive bushing depends on load, movement, speed, temperature, lubrication, shaft condition and housing fit.

What Should You Send When Requesting an Automotive Bushing?

A part number alone is not always enough, especially when the original bushing has already failed. Car seat bushings and car hinge bushings are often ordered straight from a catalogue, and the catalogue number still does not tell us the load or the movement.

For a replacement or new application, send:

  • Bushing drawing or sample
  • Shaft or pin diameter
  • Housing bore
  • Bushing length and wall thickness
  • Load
  • Movement and speed
  • Operating temperature
  • Lubrication method
  • Working environment
  • Required service life

If available, also provide information about the failed bushing. Photos of the worn surface, shaft and housing can help identify whether the problem is coming from the bushing itself or from the mating components.

FAQ

Can I select an automotive bushing from dimensions alone?

No. Dimensions determine whether the part can physically fit, but they do not determine whether the material can handle the load, movement, temperature and lubrication conditions.

Why does the same size bushing fail in one vehicle but work in another?

The dimensions may be identical while the working conditions are different. Load, oscillation angle, speed, lubrication, shaft condition and temperature can all change bushing life.

Should the shaft be replaced when replacing a bushing?

Not always. The shaft or pin should first be measured and inspected. If it has excessive wear, scoring, corrosion or an incorrect surface condition, installing a new bushing alone may not restore the required clearance.

Can a bushing be used without lubrication?

Some bushing designs are intended for dry or low-maintenance operation, while others require grease or oil. The lubrication requirement depends on the bushing construction and application conditions.

Are EV bushings different from conventional automotive bushings?

Not automatically. The correct design depends on the specific EV component. Electric motors, e-axles, battery systems and thermal-management components can introduce different combinations of temperature, load, vibration and space requirements, so the pivot has to be looked at on its own.

Can you recommend a replacement if I only have the old bushing?

A sample can be useful, but the application information is also important. If possible, provide the shaft size, housing size, load, movement, temperature and lubrication condition so the replacement can be checked against the actual working conditions.

Need Automotive Bushings?

Send us the position, the drawing or sample and the working conditions. We supply automotive seat bushings, suspension bushings, steering bushings, chassis bushings, hinge bushings and electric vehicle bushings at motor mounts and e-axles, in composite, bimetal, sintered, solid lubricated and wrapped bronze, and we come back with a material, a wall thickness and the sliding layer that suits the pivot.

Send an Inquiry

Send an Inquiry

Tell us your requirements. We'll get back to you.


Need Self-Lubricating Bearings?

Contact GLARY for bearing solutions and pricing.

Need Self-Lubricating Bearings?

Contact GLARY for bearing solutions and pricing.

后台登录