Dry Running Bushings and Oil Free Bushings
Dry running bushings for joints where oil or grease is difficult, costly or impractical to keep up. GLARY supplies oil free bushings and self-lubricating bearings that carry their own sliding layer, with no external lubrication at the bore.
Why Replace a Lubricated Bushing?
Regular lubrication is easy to overlook when a bushing sits inside an enclosed mechanism or an area that is difficult to reach. In other equipment, grease attracts dust, creates a contamination concern, or adds unnecessary maintenance work, which is where dry running bearings and oil free bushings are usually specified.
Dry running bearings offer another option. They are designed to operate without a continuous supply of external oil or grease, reducing the need for routine lubrication at selected sliding points. At those points the joint is lubrication-free by design.
However, removing the lubricant is not enough on its own. The replacement dry bearings must still handle the actual operating conditions. Otherwise, friction and wear may increase rather than improve. A design that is asked to work with no external lubrication has to be checked against the load, the speed and the temperature it will actually see.
Lubrication requirements also depend on where the bushing operates. In agricultural machinery, dust and dirt can make routine lubrication more difficult. In robotic mechanisms, access to moving joints may be limited once the equipment is assembled. The right solution depends on the actual movement and working conditions. Where access decides the maintenance interval, a self-lubricating bushing is what makes the position maintenance-free.
See our guides to Agricultural Machinery Bushings and Robot Arm Bushings for more application-specific considerations.
Can Your Existing Bushing Run Dry?
Replacing a lubricated bushing is not simply a matter of matching its dimensions. The original design may rely on an oil film, stored lubricant, or regular grease replenishment. A dry running design works differently, and an oil-free bushing has to be chosen on how the joint carries load once that film is gone.
| Your current situation | What to check before replacement |
|---|---|
| The bushing needs regular grease replenishment | Can the replacement handle the load and movement without routine external lubrication? |
| The equipment uses oil-impregnated sintered bushings | Can a material for dry sliding bearings provide the required service life under the same operating conditions? |
| The bushing wears out too quickly | Is the cause insufficient lubrication, excessive load, shaft misalignment, or surface damage? |
| The new design has no lubrication point | Can the bushing operate within its permitted load, speed, and temperature range? |
| Lubricant attracts dust or creates a contamination concern | Is a dry running design suitable for the surrounding environment and required cleanliness? |
A dry running bushing may be a good replacement when external lubrication is difficult to maintain. But if the existing dry bushing fails because of misalignment, excessive loading, or a damaged shaft, changing the material alone will not solve the underlying problem. Misalignment and overload mark the new part in the same way, and the wear pattern on the failed dry bushing is what tells the two apart.
If the dry bushing operates in a hydraulic mechanism, review the pressure, movement, and lubrication arrangement together before making a change. For equipment exposed to high loads, the replacement must also meet the required load capacity. Removing the grease point also removes the film that was carrying part of the pressure, so a position that runs with no external lubrication has to have its load capacity re-checked.
For more application-specific guidance, see Hydraulic Systems Bushings, Heavy Load Bushings and Maintenance Free Bushings.
Which Dry Running Bushing Should You Choose?
Two designs are worth considering first: PTFE composite bushings and solid lubricated bearings. They achieve low-friction operation in different ways, so the choice should follow the working conditions rather than the product name alone. Both are self-lubricating, and for dry running bushings the difference that decides the case sits in the sliding layer and in what that layer can take.

PTFE Composite Bushings
PTFE composite bushings use a low-friction sliding layer supported by a metal backing. Many designs combine a steel backing, a porous bronze layer, and a PTFE-based sliding surface. Friction stays low across the whole speed range, which is what stops a dry running bushing from sticking at the start of each stroke.
This construction is commonly used where regular external lubrication is not practical and consistent sliding performance is required. It is the usual first choice for oil free bushings that have to hold a steady friction level across millions of short movements.
Consider PTFE composite bushings when:
- The application needs low friction without continuous oil or grease supply.
- The mechanism uses repeated sliding or oscillating movement.
- Space is limited and a compact, thin-walled bushing is preferred.
- Routine lubrication would add unnecessary maintenance work.
Before selecting a grade, check the actual load, sliding speed, operating temperature, shaft finish, and required clearance. Dry running performance depends on these conditions, not on the PTFE layer alone. Wear rate and friction both move with the duty cycle, so the grade has to follow the numbers.

Solid Lubricated Bearings
Solid lubricated bearings use a metal bearing body with solid lubricant, such as graphite, incorporated into the sliding surface. During movement, the lubricant helps form a film between the bearing and shaft. The film comes from the bearing itself, so the joint stays lubrication-free with no reservoir to refill.
This design is worth evaluating when the application calls for a metal-based bearing structure and the selected material is suitable for the load, temperature, and type of movement. It is also the option to look at when the position is hot or abrasive enough that a polymer sliding layer would not survive.
Consider solid lubricated bearings when:
- The application uses slow sliding or oscillating movement.
- The design requires a metal bearing body with solid lubricant.
- The operating temperature or load makes material-specific evaluation particularly important.
- Continuous external lubrication is not available or is not desirable.
The suitable load and temperature range varies with the bearing material, lubricant arrangement, and design. Do not assume that every solid lubricated bearing can handle heavier loads or higher temperatures than a PTFE composite bushing. A maintenance-free joint still wears, and the sliding material sets the load ceiling either way.
What Can Cause Premature Wear?
A bushing designed for dry running can still wear out early if the working conditions are unsuitable. When reviewing a failed part, check the following before selecting a replacement. Each of these leaves a different mark on the bore, the pin or the housing, and the mark points to the cause.
Excessive load or sliding speed
The combination of load and speed affects frictional heat and wear. Check the pressure-velocity (PV) limit for the specific material and confirm that the actual duty cycle stays within the permitted range. Load and speed also raise friction, and the heat they generate is what shortens the life of the sliding layer.
Poor shaft surface condition
A shaft that is too rough, damaged, or unsuitable for the bearing material can accelerate wear. Shaft hardness, surface finish, and dimensional accuracy should be checked against the selected bushing's requirements. A rough counterface cuts into the layer, and the wear then runs away from the original clearance.
Misalignment or uneven loading
If the shaft and housing are not properly aligned, the load may concentrate on one side of the sliding surface. This can lead to uneven wear even when the nominal load appears acceptable. The loaded band narrows to one edge, so the wear lands where the material is least able to carry it.
Excessive temperature
Friction generates heat, and the operating temperature can rise further under continuous movement or high loading. Check both the ambient temperature and the temperature expected at the sliding interface. Above the working range of the sliding layer, friction stops being steady and the wear rate climbs with every cycle.
Incorrect clearance or installation
An unsuitable fit or installation method can restrict movement or create excessive clearance. Confirm the housing dimensions, shaft dimensions, tolerances, and recommended installation procedure before fitting the replacement. A dry running bushing is less forgiving of a poor fit than a greased bronze one, because there is no film to absorb it.
Temperature and load often need to be evaluated together. A bushing that performs well under moderate conditions may not be suitable when the sliding surface becomes hotter or the load increases. If either factor is a major concern, review the operating limits before selecting a replacement. A maintenance-free design still has a PV limit, and that limit is lower once the joint runs dry.
See High Temperature Bushings and Heavy Load Bushings for more information on these operating conditions.
A maintenance-free design should not be treated as a wear-free design. Eliminating routine lubrication does not eliminate the need to select the correct material and inspect the equipment when its operating conditions require it. A self-lubricating grade removes the grease point, so the inspection interval has to be set on the duty itself.
What Should You Confirm Before Ordering?
If you are sourcing an oil-free bushing to replace an existing part, the following information will help determine whether a dry running design is suitable. The same list applies to oil free bushings bought for a new build, where no external lubrication is planned from the start.
- Dimensions: Shaft diameter, bushing inside diameter, outside diameter, length, and required tolerances.
- Load: Radial load, load direction, and any impact or shock loading.
- Movement: Continuous rotation, linear sliding, oscillation, or intermittent movement.
- Speed and duty cycle: Sliding speed, oscillation frequency, operating hours, and start-stop frequency.
- Temperature: Ambient temperature and expected temperature at the sliding surface.
- Shaft condition: Material, hardness, surface finish, and alignment.
- Current lubrication method: Grease, oil, oil-impregnated material, or no external lubrication.
- Existing problem: Frequent lubrication, contamination, excessive wear, noise, or difficult maintenance.
A drawing, a photo of the existing bushing, or its current part number can also help clarify the replacement requirements. An existing part number on the oil-free bushing identifies the construction faster than a measurement does, and it tells us whether the original was a lubricated or a lubrication-free type.
GLARY can assess the available information against the relevant bushing design and material data. Final selection should be based on the actual operating conditions, not dimensions alone. The same review decides whether a dry running bushing will last in the position or wear out inside the first months.
FAQ
Can I use the same bushing dimensions when switching to a dry running design?
Not always. The replacement may require different running clearance, shaft tolerances, or housing fits. Check the recommended fit for the selected bushing rather than relying only on the dimensions of the original part. The dry running bushing also runs at a different clearance, and that is the part most often got wrong.
Does the shaft need to be changed when fitting a dry running bushing?
Not necessarily. It depends on the shaft's material, hardness, surface finish, condition, and compatibility with the new sliding material. Inspecting the existing shaft before replacement can help avoid premature wear. Oil free bushings tolerate a corroded counterface less well than a greased bronze one, so a worn shaft is worth measuring before the change.
What information should I send when requesting a dry running bushing?
Provide the bushing dimensions, load, speed or movement type, operating temperature, shaft details, and current lubrication method. A drawing or photo of the existing part is also useful. This information helps determine whether a PTFE composite bushing or a solid lubricated bearing is suitable, and whether dry running bushings can be made maintenance-free in that position at all.
Need to Replace a Lubricated Bushing?
If regular lubrication is difficult to maintain, GLARY can help you assess whether a dry running bushing is suitable for your equipment. The same assessment covers oil free bushings for a new build, where the grease point is being designed out.
Send us your bushing dimensions, operating conditions, and current lubrication method. A drawing or photo of the existing part is also helpful when evaluating a replacement. With those details we can compare the position against a self-lubricating grade and tell you what it will do with no external lubrication at the bore.
Need Self-Lubricating Bearings?
Contact GLARY for bearing solutions and pricing.
