Hydraulic Systems Bushings

Bushings for hydraulic motors, actuators and other moving parts. The type follows the movement at the joint, the load it carries, the condition of the shaft and how that position is lubricated.

Where Are Bushings Used in Hydraulic Systems?

Hydraulic system bushings are used where a shaft, rod or pin moves against a housing or another part. The load and the movement are not the same throughout a hydraulic system, and that is why the position matters.

Hydraulic motor with the drive shaft and two port fittings
Hydraulic motor: the shaft support position

Hydraulic Motor Shaft Support

Hydraulic motor bushings support a rotating shaft inside the motor and keep it in position while it turns under load.

Typical conditions: rotation, radial load, hydraulic fluid and pressure.
Hydraulic actuator with a rod extending at each end
Hydraulic actuator: the pivot and linkage positions

Hydraulic Actuator Pivot and Linkage Points

Hydraulic actuator bushings sit around the pins at linkages, clevises and pivot joints. The bushing takes the load while the joint moves back and forth.

Typical conditions: oscillation, load, shock and side load.
Hydraulic cylinders with rod ends and mounting eyes
Hydraulic cylinder: the rod end and support positions

Hydraulic Cylinder Rod and Support Positions

Hydraulic cylinder bushings sit at the bearing positions that guide and support the piston rod and the other moving parts during reciprocation.

For cylinder-specific applications, see Hydraulic Cylinder Bushings.
Hydraulic valve block with its control ports
Hydraulic valve: the stem and spool guide positions

Hydraulic Valve Stem and Spool Guides

Some hydraulic valves have a stem or spool that moves repeatedly inside a guide. Hydraulic valve bushings at that position have to suit the movement, the clearance and the lubrication conditions.

For valve applications, see Valve Stem Bushings and Valve Components Bushings.

Other Rotating Hydraulic Components

Bushings can also be used around rotating shafts in other hydraulic components where the shaft needs support and controlled clearance. Inside a gear pump body, hydraulic pump bushings carry the shafts that turn the gears.

For gear pump applications, see Hydraulic Gear Pump Bushings.

The Bushing Has to Match the Movement

The same bushing does not work the same way in every hydraulic component. Start with how the shaft, rod or pin actually moves.

Continuous Rotation

Common in hydraulic motors and other rotating components. Hydraulic motor bushings see continuous shaft rotation, and speed, radial load, shaft surface and lubrication all affect wear.

Reciprocating Movement

Common around piston rods and other parts that move back and forth. The direction changes repeatedly during operation, and side load, stroke, load and lubrication all affect bushing life.

Oscillating Movement

Common at actuator pivots and linkage points. The shaft moves through a limited angle rather than making a full rotation, and actuator bushings in these positions can see high loads, shock and uneven contact.

What Causes a Hydraulic Bushing to Wear?

Hydraulic system bushings rarely wear out because of the material alone. The shaft, the housing, the alignment and the lubrication all belong in the check.

01Too Much Load. A bushing carrying more load than expected can wear quickly, and shock or side loads make the problem worse.
02Repeated Movement. Rotation, reciprocation and oscillation produce different wear patterns. A material that works well for one type of movement may not suit another.
03Poor Lubrication. Some bushings rely on oil or grease, and if the supply is insufficient, friction and wear increase. Other positions need a bushing that runs with little or no additional lubrication.
04Shaft Problems. A rough, damaged or worn shaft shortens bushing life, so check the surface before a replacement goes in.
05Misalignment. When the shaft and the housing are not properly aligned, the load concentrates on one part of the bushing instead of spreading across the bearing surface.

What Tells You the Bushing Needs to Be Replaced?

Look at how the machine moves, as well as at the hydraulic bushings themselves.

Common signs include:

  • More play between the shaft and the housing
  • Excessive movement of a rod or pin
  • Uneven or jerky movement
  • Increasing vibration
  • Abnormal noise
  • Visible scoring or wear on the bushing
  • Increasing clearance
  • Faster wear after a recent replacement
  • Repeated lubrication or maintenance problems

These signs can also come from the shaft, the housing, the alignment or the lubrication. Check those parts before installing a replacement bushing.

What Happens If a Worn Bushing Is Left in Service?

A worn bushing usually starts with more clearance. The problem can then spread to other parts.

Hydraulic cylinder with the piston rod sheared off at the gland
A piston rod sheared at the gland face
Splined shaft with the spline teeth twisted and sheared off
A splined shaft twisted off at the spline
  1. Bushing wear
  2. Clearance increases
  3. Shaft, rod or pin moves more than it should
  4. Load becomes uneven
  5. Shaft, housing or nearby components wear faster
  6. More maintenance and unexpected downtime

Hydraulic bushings are usually inexpensive compared with the parts around them. If excessive clearance is left unchecked, the shaft or the housing may also need repair or replacement.

Which Bushing Type Fits the Application?

Different positions can need different hydraulic system bushings. Start with the load, the movement and the lubrication at the actual bearing position.

Composite Bushings

Composite Bushings

Composite bushings are a common choice where low friction and good wear resistance are needed. Depending on the construction, they can handle rotating, reciprocating or oscillating movement.

They are worth considering when lubrication is limited, or when the bushing needs to work with little maintenance.

Typical considerations: low friction, wear resistance, limited lubrication, rotation or reciprocation.
View Composite Bushings
Bimetal Bearings

Bimetal Bearings

Bimetal bearings are suited to higher-load positions where oil or grease lubrication is available.

They suit hydraulic components exposed to heavy loads, shock or oscillating movement.

Typical considerations: high load, shock load, oscillation, oil or grease lubrication.
View Bimetal Bearings
Solid Lubricated Bearings

Solid Lubricated Bearings

Solid lubricated bearings are suited to heavily loaded, slower-moving positions where regular lubrication is difficult.

They are a practical option for hydraulic actuator bushings at pivots and other heavy-duty joints.

Typical considerations: high load, low speed, oscillation, limited lubrication.
View Solid Lubricated Bearings
Sintered Bushings

Sintered Bushings

Sintered bushings suit rotating positions where an oil-impregnated bearing and a compact design fit the space.

Typical considerations: rotation, oil impregnation, compact space.
View Sintered Bushings
Bronze Wrapped Bushings

Bronze Wrapped Bushings

Bronze wrapped bushings are an option for lubricated bearing positions carrying substantial loads.

Typical considerations: high load, shock, regular lubrication.
View Bronze Wrapped Bushings

What Information Is Needed to Choose the Right Bushing?

A machine name alone is usually not enough to pick a hydraulic system bushing. We need to know what the bushing actually does.

1

Where is the bushing installed?

Tell us the component and the bearing position. A drawing or a photo with the position marked is even better.

2

How does it move?

  • Continuous rotation
  • Oscillation
  • Reciprocation
3

What load does it carry?

Include the radial load where you know it, and tell us if the position also sees side load, shock or changing loads.

4

What is the shaft size and condition?

Useful information includes:

  • Shaft diameter
  • Housing diameter
  • Bushing length
  • Shaft material
  • Shaft hardness, if known
  • Surface finish, if known
5

How fast does it move?

For rotating parts, give us the shaft speed. For reciprocating parts, give us the stroke and the cycle rate where you have them.

6

How is it lubricated?

Tell us whether the position runs with:

  • Hydraulic oil
  • Grease
  • Limited lubrication
  • No additional lubrication
7

What is the working environment?

Temperature, contamination, water exposure and the hydraulic fluid can all affect material selection.

8

Do you have a drawing or an existing part?

Send the drawing, the dimensions or the current bushing number if you have one. We can check the required dimensions and the working conditions before recommending a bushing type.

FAQ

Can a hydraulic bushing run directly in hydraulic oil?

It depends on the bushing material and construction. Some materials are intended for lubricated operation and can work with hydraulic fluids, while others are selected for dry or limited-lubrication conditions. The specific hydraulic fluid should be checked against the bearing material.

Does hydraulic pressure determine the bushing type?

No. Hydraulic pressure creates the working force in the system, and the hydraulic system bushing sees a mechanical load at its own installation position. Shaft movement, load, speed, lubrication, temperature and shaft condition all matter as well.

Can one bushing material be used throughout a hydraulic system?

Not usually. Hydraulic motor bushings turn continuously with the shaft, while hydraulic actuator bushings at a pivot oscillate under a much higher load. The two positions can need different constructions even when they are part of the same machine.

Can the same bushing be used for rotation and reciprocation?

Some bushing materials can handle both, but the operating conditions still have to be checked. Speed, load, movement frequency, lubrication and shaft condition can all change how suitable a material is.

What shaft information should I provide when requesting a hydraulic bushing?

At minimum, the shaft diameter, the housing diameter, the bushing length and the application. If you have them, also send the load, the speed or stroke, the lubrication method, the temperature and the shaft surface condition. A drawing of the existing part is the easiest way to avoid missing important dimensions.

Do you make custom hydraulic bushings?

Yes. We can review drawings, dimensions and working conditions for non-standard hydraulic bushings and help work out a suitable construction.

Need a Hydraulic Bushing for a Specific Application?

Send us the bushing dimensions, the drawing or the application details. If you are not sure which type to use, tell us where the bushing is installed and how it moves.

Send an Inquiry

Tell us your requirements. We'll get back to you.


Need Self-Lubricating Bearings?

Contact GLARY for bearing solutions and pricing.

Need Self-Lubricating Bearings?

Contact GLARY for bearing solutions and pricing.

后台登录