Heavy Load Bushings

For high loads, impact and slow movement. Heavy load bushings, high load low speed bushings, heavy duty bushings and shock load bushings are sized on bearing pressure and the peak load in the cycle, and made to drawing, sample or stated dimensions.

Not All Heavy Loads Are the Same

A heavy load bushing does not work under the same conditions in every machine. The way a load acts on the bearing matters as much as the load itself, and on heavy machinery the same joint can see three different patterns.

Steady Load

A heavy load bushing supports a relatively consistent force. Bearing pressure and the distribution of contact across the sliding surface are important when assessing wear and long-term performance.

Impact Load

The force changes suddenly when equipment hits an obstacle, changes direction or engages with a loaded component. Peak loads can be much higher than the normal operating load, so average load alone may not give a reliable picture of the actual conditions. Shock load bushings are sized on that peak figure.

High Load at Low Speed

High load low speed bushings often work in joints that carry a high force while moving through only a small angle. This type of oscillation can concentrate wear in a limited area rather than distributing it around the full bearing surface.

These differences matter when specifying heavy load bushings and heavy duty bushings. A design that works well under a steady load may not be the right choice for repeated impact, shock load or short-angle oscillation, which is the normal duty of high load low speed bushings on heavy machinery and where the wear concentrates.

Heavy loads occur in different ways across industrial equipment. Excavator boom and bucket joints face high forces during digging, while crane pivots carry loads as the boom and lifting mechanism move. In both cases, the pin, bushing and housing must work together to maintain proper contact under load.

For equipment-specific considerations, see our guides to Excavator Bushings and Crane Bushings.

Where Does the Load Go When a Machine Moves?

In a typical pin joint, the load passes from the moving component through the pin and bushing into the housing. The bushing provides the sliding surface and helps distribute the force across the joint, and on shock load bushings and impact load bushings that path also carries the impact peak that arrives with each reversal.

Problems arise when the load is not distributed as intended.

Mechanical ConditionWhat It Can Mean for the Bushing
Pin deflection under loadContact pressure may become concentrated toward one side
Misalignment between connected partsThe bushing may experience uneven contact along its length
Worn or oversized housing boreThe bushing may lose proper support or move in the housing
Clearance outside the design rangeMovement, impact and local contact conditions may change
Repeated changes in load directionDifferent areas of the sliding surface may experience alternating contact

These conditions are particularly relevant to heavy machinery with large pins, long linkages and oscillating joints, which is where high load bushings and shock load bushings carry the highest contact pressure.

A stronger bearing material will not automatically solve a problem caused by poor alignment or insufficient housing support. Before selecting a replacement, determine whether the original failure came from the bushing itself or from the surrounding assembly, because a new bushing will follow the same wear pattern if the cause sits outside it.

In a loaded joint, the bushing does not work alone. Pin deflection, worn mating parts or misalignment can concentrate contact on one side of the bearing surface. This may cause uneven wear even when the nominal load is within the bushing's rated range.

These issues are common in pivot pins, hinges and linkages that move repeatedly under load. Read more in our guide to Mechanical Joints Bushings.

When Load, Speed and Lubrication Work Against Each Other

Load, sliding speed and lubrication need to be considered together. Changing one operating condition can affect how the bushing performs under the others.

Pressure and PV Value

Bearing pressure describes the load carried over the projected bearing area. For many sliding bearing materials, the PV value combines bearing pressure and sliding speed:

PV = P × V

Here, P is the bearing pressure and V is the sliding speed. The allowable PV value depends on the specific bearing material and operating conditions.

PV is useful for comparing operating conditions, but impact peaks, edge loading and oscillating movement need separate checks against the manufacturer's design limits.

Low Speed and Oscillation

High load low speed bushings often work in joints that reverse direction repeatedly. Because movement may be limited, the sliding surface can experience localized wear. The oscillation angle, frequency and duration of each cycle should therefore be considered during selection.

Lubrication Under Load

Lubrication requirements depend on the bearing construction and operating conditions. In grease-lubricated designs, the lubricant must reach the loaded surface. Where routine lubrication is impractical, a suitable solid-lubricated bearing may be worth evaluating.

What matters is a design that stays within its limits throughout the actual duty cycle, and high load bushings are no exception: the rating on its own does not decide the selection.

Choosing a Bushing for the Actual Load Condition

Three bushing types are worth evaluating for heavy load bushings. The right choice depends on the required load capacity, movement, lubrication and operating environment.

Bushing TypeWhen to Consider ItWhat Needs Verification
Bimetal Bearings →Heavily loaded joints where external lubrication is availableLoad capacity, peak pressure, shaft condition and lubrication arrangement
Solid Lubricated Bearings →High-load sliding positions where regular external lubrication is difficultMaterial load limits, sliding speed, temperature and oscillation conditions
Bronze Wrapped Bearings →Lubricated pin joints and oscillating applications with suitable bearing supportLoad limits, lubrication supply, impact severity and housing dimensions
Bimetal bearings with a steel backing and a sintered bronze layer

Bimetal Bearings

Bimetal bearings are worth evaluating for heavily loaded joints that use an appropriate lubrication system. The steel backing provides structural support, while the bearing layer and its lubrication arrangement must suit the actual load and movement.

For impact-loaded applications and shock load bushings, check the peak force and the support provided by the shaft and housing rather than relying on a nominal load rating alone.

View Bimetal Bearings
Solid lubricated bronze bearings with graphite plugs

Solid Lubricated Bearings

Solid lubricated bearings are an option for heavy-duty sliding points where routine grease supply is difficult or impractical. Their suitability depends on the bearing material, solid lubricant configuration, contact pressure and operating temperature.

They should not be assumed suitable for every impact-loaded joint. Confirm the limits of the specific design before selecting it.

View Solid Lubricated Bearings
Bronze wrapped bushings with diamond lubrication pockets

Bronze Wrapped Bearings

Bronze wrapped bearings suit lubricated pivots and linkage joints where the design provides sufficient load capacity and support. Lubrication method, bearing dimensions and the condition of the mating pin all affect performance.

For severe shock loads or concentrated contact, verify the specific bearing's limits before using it as a replacement.

View Bronze Wrapped Bearings

The three types serve different purposes, and heavy duty bushings are not ranked by material alone. The final choice should be based on operating data and the actual assembly rather than on a general ranking of materials.

The right bushing also depends on where it is installed and how the machine moves. Excavators, cranes and press machines can all involve heavy loads, but their movement patterns, peak forces and lubrication conditions are different.

Explore our application guides for Excavator Bushings, Crane Bushings and Press Machine Bushings to see how these operating conditions affect bushing selection.

Before You Specify a Replacement

A replacement bushing should fit the mechanical assembly and the operating conditions. On heavy load bushings, high load bushings and heavy duty bushings, matching the original dimensions is only the starting point.

Before confirming a heavy load bushing, establish:

  • Normal and peak load: Include impact loads if they occur during the operating cycle.
  • Movement: Specify continuous rotation, short-angle oscillation or reciprocating movement.
  • Lubrication: Identify the existing lubrication method and whether it can be maintained in service.
  • Assembly dimensions: Confirm the bushing bore, outside diameter, length, housing fit and required operating clearance.
  • Mating components: Check the pin diameter, shaft condition, hardness and surface finish where applicable.
  • Operating environment: Record temperature and exposure to dust, water or other contaminants.

If the existing heavy load bushing has failed repeatedly, provide the wear pattern and any available assembly drawings. These details can help distinguish a material selection problem from misalignment, inadequate support or unsuitable operating clearance.

For custom or replacement heavy load bushings, this information is more useful than specifying the application name alone.

If you are replacing a worn bushing, check more than its inside and outside diameters. The application matters too: a slow oscillating pivot, a frequently loaded linkage and a press mechanism may require different bearing designs.

When requesting a replacement, provide the dimensions, load conditions, movement pattern and lubrication method. If the bushing is used in a specific machine, our guides to Excavator Bushings and Mechanical Joints Bushings may also help you identify the relevant operating conditions.

FAQ

Can a heavy load bushing be replaced without changing the housing?

Often, yes, provided the housing bore remains within the required dimensional and geometric tolerances. If the bore is worn, out of round or damaged, a new bushing may not receive adequate support. Measure the housing before confirming the replacement dimensions.

Should the replacement bushing have the same wall thickness as the original?

Not necessarily, but changing wall thickness affects the finished bore, outside diameter, clearance and available space for the bearing layer. Check the installed dimensions and housing fit before changing the design.

Does a harder shaft always improve bushing life?

No. Shaft hardness is only one factor. Surface finish, alignment, lubrication and compatibility between the shaft and bearing material also affect wear. An unsuitable shaft surface can shorten bearing life even when the shaft is sufficiently hard.

Can a heavy load bushing be designed to fit an existing worn pin?

A bushing can be manufactured to specified dimensions, but it should not be used to compensate for an unmeasured or badly worn pin. First establish the pin's actual diameter, straightness and surface condition. If the pin is outside its service limits, repair or replacement may be necessary.

What should I provide when requesting a custom heavy-duty bushing?

A dimensioned drawing is the best starting point. Include the required finished dimensions, material or existing part specification if known, operating load, movement, lubrication method and working environment. If the part is a replacement, photos of the assembly and the failed bushing can also help clarify the design requirements.

Need a Bushing for a Heavy-Load Application?

Share your bushing dimensions, load conditions and operating requirements. GLARY can help you evaluate a suitable bushing type for your application.

Send an Inquiry

Tell us your requirements. We'll get back to you.


Need Self-Lubricating Bearings?

Contact GLARY for bearing solutions and pricing.

Need Self-Lubricating Bearings?

Contact GLARY for bearing solutions and pricing.

后台登录