Gear Shift Bushings

Gear Shift Bushings

Gear Shift Linkage Bushings: the shift rod, selector fork or cable linkage that carries the driver's shift movement into the gearbox. Custom sizes available for replacement and OEM applications.

Where the Gear Shift Bushing Sits

Several positions in a gear Shift Bushing assembly carry these bushings. The exact arrangement depends on the machine, but these are the usual locations.

01

Shift rod / selector rod pivot

The rod that transfers movement from the lever to the gearbox.

02

Selector fork shaft

The shaft the fork slides on inside the gearbox.

03

External linkage joints

Ball-joint and pivot positions on the external shift mechanism.

04

Cable end fittings

Where a cable linkage terminates at a lever.

What the Gear Shift Bushing Does

A bushing holds a moving member in place, carries its load and takes the wear so the shaft does not have to.

01

Carries the load

Keeps the bore in shape

Load passes from the moving member through the bushing into the housing. The POM composite construction is chosen so the bore holds its shape under that load.

02

Controls friction

Movement without stick-slip

The bearing surface sets the friction level for repeated back-and-forth movement. Without it the drive has to break the joint free every time it starts moving.

03

Keeps alignment

Holds the axis

It holds the moving member on its axis for the whole stroke.

04

Takes the wear

The sacrificial part

The bushing wears so the pin, shaft or housing does not. Bushings are replaced as a service item; a shaft is not.

Why POM composite Suits This Position

This position is a good fit for POM composite: a POM (acetal) bearing shell on a steel backing.

  • It carries more load than PTFE composite and still runs dry.
  • The bearing wall is thicker, which helps when the load is unevenly distributed or the bore is slightly out of line.
  • Wear resistance under oscillating movement is good, and oscillating movement is where PTFE grades wear faster.
  • It absorbs impact better than a bronze bushing, so the joint runs quieter.

Where it does not fit: Friction is higher than PTFE, and the material needs some sliding speed before its lubrication develops.

Signs the Part Is Worn

These symptoms mean the part is on its way out.

  • Visible clearance at the joint. The moving member rocks when you push it.
  • Knocking or rattle that was not there when the machine was new
  • The bore is oval, scored, or has a step worn into one side
  • The bore surface is discoloured or blackened from local heat
  • Grease is being pushed out of the joint, or the position has run dry
  • The pin or shaft is worn as well

What It Costs If You Leave It

A worn part rarely stays the only damaged one.

  • Wear speeds up. Once there is clearance, the joint starts taking impact instead of sliding, and the wear rate climbs.
  • The pin or shaft begins to wear. A shaft or a machined housing costs several times what a bushing costs.
  • The housing bore can be damaged, which turns a consumable part into a machining job.
  • Vibration rises through the assembly and can work fasteners loose elsewhere.
  • The failure usually shows up mid-production instead of during a planned stop, so the cost is the downtime.

Which GLARY Products Fit

These are the families that suit this position. The parameters that separate them are in the next section.

POM Composite Bushings

POM Composite Bushings

View product →
PTFE Composite Bushings

PTFE Composite Bushings

View product →
Sintered Bushings

Sintered Bushings

View product →

How to Choose Between Them

Four things decide the material. Send us these and we can name a part instead of sending a catalogue.

ParameterWhat decides it
Sliding speedmoderate
Loadmedium
Lubricationnone, or a trace of grease
Temperature−40 °C to +130 °C
Environmentdry and dusty

FAQ

Frequently Asked Questions

Will a different material change the shift feel?+

It can. A bushing with lower friction usually gives a lighter, more positive shift, but the clearance has to be right or the lever will feel loose.

How do I identify the right part from the old one?+

Measure the inside diameter, outside diameter and length, and note whether there is a flange. Those three dimensions plus a photo are usually enough to identify it.

Can a self-lubricating bushing replace a greased one?+

Usually, if the load and temperature sit inside the self-lubricating material's range. The mating surface has to be smooth and hard enough, and the clearance may need checking because these materials expand at a different rate from bronze.

Do you make non-standard sizes?+

Yes, to drawing, sample or stated dimensions. Standard materials in common sizes carry the lowest minimum order.

Send an Inquiry

Send an Inquiry

Tell us your requirements. We'll get back to you.


Need Self-Lubricating Bearings?

Contact GLARY for bearing solutions and pricing.

Need Self-Lubricating Bearings?

Contact GLARY for bearing solutions and pricing.

后台登录